SunSDR2 PRO
SunSDR2 PRO
SunSDR2 PRO
SunSDR2 PRO
, ,

SunSDR2 PRO HF, 6m & 2m Transceiver

(2 customer reviews)
Availability:

In stock (can be backordered)

SunSDR2 PRO is a direct sampling SDR transceiver developed for serious DXing and contesting. It covers all HF bands plus 50 MHz and 144 MHz VHF bands with a general coverage receiver. It combines high performance in a small package and has a LAN interface for maximum flexibility. Remote control over DSL or mobile 3G and 4G connections provide a full SDR experience using the Expert Remote System.

2,114.57 $

  • EUR: 1,990.00 €
  • SEK: 23 297 kr

In stock (can be backordered)

unlimited available through backorder

ModMic USB Attachable Boom Microphone

The New ModMic USB Attachable Boom Microphone is great for SDR Transceivers where the mic connects to the PC. The ModMic Uni is a high quality uni-directional electret microphone on a boom that attaches to any headphones to create your perfect headset.

Samlex SEC-1212G 13.8 Volt at 9.5 Amp

Efficient 13.8V/9.5A power supply with reliable, clean and highly filtered power specifically developed for demanding radio equipment.

2,549.07 $ for 3 item(s)

The SunSDR2 PRO transceiver was designed for advanced operation on HF and VHF bands, even the most demanding operator will be surprised by its capabilities. Modern hardware along with the ExpertSDR software makes this high-performance SDR transceiver the perfect base station and at the same time perfectly suitable for field operations.

SunSDR2 PRO Main Capabilities

  • Independent RX path based on DDC (Direct Down-Conversion) architecture
  • Independent TX path based on DUC (Direct Up-Conversion) architecture
  • 2 software RXs + SubRX for each of them (4 slices total) + independent wideband Bandscope up to 80 MHz
  • A remote control operation, using it, you connect PTT and CW-key to the E-Coder panel. Microphone and E-Coder are connected to the remotely set up PC
  • TCI interface for seamless connection with third-party software, the list of software with TCI support
  • Professional TX processing module provides the most advanced tuning capability for voice operation
  • ExtCTRL connector to control external devices with 8 powerful keys with open collector
  • ALC connector for external power amplifiers*
  • Supports use of VHF transverters**
  • An opportunity to use the transceiver as a signal generator via DAC OUT connector (SMA connector)
  • An opportunity to use external filters in the middle of the RF path, using ADC IN and RX OUT (SMA connector)
  • Monitoring delay in CW mode is about 5-6 ms
  • Input for external 10 MHz reference oscillator
  • An opportunity to use the transceiver in SO2V mode
  • Full duplex or half-duplex modes***
  • Antenna switch with 2 HF antenna connectors and separate VHF antenna connector (Mini UHF connectors)
  • Internal power-meter for HF and VHF bands and SWR-meter for HF band
  • Ethernet LAN interface provides a fast and reliable connection to PC

* ** *** These functions are supported by the transceiver’s hardware, but are not implemented in the ExpertSDR2 software. They will be supported in the future ExpertSDR2 software releases.

SunSDR2 PRO Block Diagram

SunSDR2 PRO Specifications

RF ADC, bit @ MHz 16 @ 160
ADC type LTC2209
RX Frequency range HF 0.1 to 65 MHz, VHF 95 to 155 MHz
Independent software receivers 2 + 2 SubRX
Sample rate, kHz @ bit 39; 78; 156; 312 @ 24
Bandscope, MHz 80
RX HF filters, MHz 65 MHz LPF or 9 x octave BPF
RX VHF filters, MHz WideRX: 95-155 or SAW filter for 2M: 144-148
BDR on HF, dB 130
BDR on VHF, dB 114
Sensitivity, uV 0.2
DR IMD3, not less dB 98
RMDR, dB 110
ATT/Preamp, dB -20; -10; 0; +10
VHF LNA, dB +22
RF DAC, bit @ MHz 14 @ 640
TX Frequency range, M All amateur bands 160-6; 2
Output power on HF, W 15 (up to 20)
Output power on 6M, W 15
Output power on VHF, W 7 (up to 8)
TX IMD3, dB 25-30 on HF/VHF
Local oscillator TCXO, MHz +/- ppm 20 +/- 0.5
External 10 MHz oscillator input +
Built-in audio codec, bit 24
RF input/output 2HF, 1VHF (Mini_UHF)
ADC IN, DAC OUT (SMA)
PC interface LAN 100 Mbit
DC voltage range in RX/TX, V 10…16/ 12…16
Recommended DC voltage, V 15
Current consumption RX/TX, A 1.25 / 5
Power consumption RX/TX, W 19 / 75
Operating temperature, °C/°F 0…+50/ +32…+122
Dimensions L x W x H, cm/inches 19.0 x 17.0 x 5.0/ 7.48 x 6.69 x 1.97
Weight, kg/lbs 1.5/ 3.31

Specifications are subject to change without notice or obligation and specifications are only guaranteed within the amateur radio bands.

SunSDR2 PRO – What’s in the Box

  • SunSDR2 PRO Transceiver
  • LAN-cable 1.8m for connecting to local network
  • Power cable 2.0m for connecting to power supply
  • Two 6.3mm phono male to 3.5mm phono female adapters to connect a headset to the radio
  • Mini UHF (male) to SO239 (UHF/PL female) pigtail adapter with 30 cm  RG58 coax.

SunSDR2 PRO Recommended Accessories

SKU: SS2PRO Categories: , ,
Weight 2.38 kg
Dimensions 32 × 24 × 9 cm

Based on 2 reviews

5.0 overall
2
0
0
0
0

Add a review

This site uses Akismet to reduce spam. Learn how your comment data is processed.

  1. Marc (verified owner) –

    Totally different level from traditional radio!
    Tons of custom settings, super nice filters, waterfall, bandscope, t.eq, etc, etc

    Superb Forum & Support!

    Marc –

  2. Tilman, SM0JZT –

    20W may not sound like a big number, but ample of power for day to day traffic. If you need more output, just put a amplifier behind.
    Nice to be able to run 2m with a useful spectrum view in the normally very uncrowded band.

    Tilman, SM0JZT

    Tilman, SM0JZT –

Related products

Got Questions ? Call us! +46 735649805
Contact Info
Pileup Communications
Box 38071, 100 64 Stockholm, Sweden
support@pileupdx.com

Pileup AB is a EU VAT registered business (SE559004438301)
VOEC : 3013359
© Pileup AB - All Rights Reserved.
Got Questions ? Call us! +46 735649805