ColibriNANO USB SDR Receiver 0.1 to 55 MHz
Out of stock
Share this:
ColibriNano takes USB dongle SDR receivers to a new level. This is a direct sampling, high quality SDR receiver covering 100 kHz to 55 MHz with up to 3 MHz sample rate in a sturdy aluminium USB stick.
- ARRL/QST Review by VA2PV
- Review by Adam Farson, VA70J/AB40
- Review on the Fenu-Radio
- Video review by Z33T Mile Kokotov
325.00 €
Out of stock
-
Expert Electronics, Receivers
ColibriNANO USB SDR Receiver 0.1 to 55 MHz
ColibriNano takes USB dongle SDR receivers to a new level. This is a direct sampling, high quality SDR receiver covering 100 kHz to 55 MHz with up to 3 MHz sample rate in a sturdy aluminium USB stick.
- ARRL/QST Review by VA2PV
- Review by Adam Farson, VA70J/AB40
- Review on the Fenu-Radio
- Video review by Z33T Mile Kokotov
SKU: ColibriNANO -
-
Controllers, Receiver Accessories, Transceiver Accessories
ShuttleXpress
ShuttleXpress is the perfect controller for your SDR
ShuttleXpress is a compact multi-media controller that gives you programmability and ergonomic control over ExpertSDR2 PRO and other popular multi-media applications. It lets you control any feature of your SDR transceiver or receiver that is accessible via keyboard shortcuts. Its the perfect accessory for ColibriDDC and SunSDR2 PRO, and it can also be used in applications with conventional transceivers.
SKU: SHUTTLEX
The ColibriNANO opens new horizons for HF band enthusiasts, thanks to its 14-bit ADC, which provides a ~110 dB BDR and up to 3 MHz sample rate. A 0.5 ppm local oscillator gives the ColibriNANO a great frequency stability.
Using the ColibriNANO remotely, located in a rural area will let you receive weak signals otherwise impossible to hear in the noise. Remote control your Colibri NANO from anywhere over the internet using our RPI server
The ColibriNANO operated by ExpertSDR2 software and compatible with popular HAM software such as HDSDR, SDRSharp via the ExtIO library.
ColibriNANO Block Diagram
The ColibriNANO features a Texas Instruments ADS4145 14 bit direct sampling ADC and a built in 55 MHz low pass filter that can be bypassed to receive signals up to 500 MHz (external filters like the our 2m filtered preamp recommended 100 MHz high pass filter recommended).
With the external ExtIO library the ColibriNANO can be used with third party software like HDSDR etc.
This is not a cheap USB dongle found on Ebay, this high performance SDR receiver is developed by Expert Electronics and features a sturdy aluminium chassis, ESD protection, USB 2.0 interface and a quality SMA antenna connector.
Best of all, the ColibriNANO travels in your pocket and only needs your computer and an antenna! Its the ultimate portable SDR receiver!
Remote Control
The ColibriNANO can be controlled via Internet using ExpertRemote,  a client-server system that allows you to place the receiver and server in a remote quiet location with good RX antennas and control and listen from any place where you have an internet connection available. The receiver’s software can be synchronized with transceivers and be used as a panadapter with high resolution.
Software support
- ExpertSDR2
- CW Skimmer
- Skimmer Server
- Third party software using ExtIO library
ColibriNANO Architecture
ColibriNANO Specifications
| RF ADC, bit @ MHz | 14 @ 122.88 |
| ADC type | ADS4145 |
| RX Frequency range, MHz | 0.1…55 |
| Undersampling, MHz | 0.1…500 |
| Independent software receivers | 1 + 1 SubRX |
| Sample rate, kHz @ bit | 48; 96; 192; 384; 768 @ 24 1536; 1920; 2560; 3072 @ 16 |
| Bandscope, MHz | – |
| RX HF filters, MHz | LPF: 55 |
| Noise floor, dBm | 1.9 MHz (160M) – 131 7.1 MHz (40M) – 130 52.5 MHz (6M) – 127 |
| NPR (Noise Power Ratio) with Noise Bandwidth 5 MHz, dB | 59 |
| BDR on HF, dB | 110 |
| BDR on VHF, dB | n/s |
| Sensitivity, uV | 0.35 |
| DR IMD3, not less dB | 95 |
| RMDR, dB | 104 |
| ATT/Preamp, dB | from -31.5 to +6, with 0.5 step |
| Local oscillator TCXO, MHz +/- ppm | 122.88 +/- 0.5 |
| Built-in audio codec, bit | – |
| RF input with up to 15 kV ESD protection | 1 SMA connector |
| Maximum antenna input voltage, without ADC overload, mV (ATT=0 dB) | 74 (Pk-Pk); 32.7 (RMS) |
| PC interface | USB 2.0 |
| DC voltage range, V | 4.5…5.5 |
| Current consumption, A | 0.41 |
| Power consumption, W | 2.02 |
| Operating temperature, °C/°F | 0…+50/ +32…+122 |
| Active device temperature, °C | +45…+50 |
| Dimensions L x W x H, cm/inches | 9.0 x 2.5 x 1.7/ 3.54 x 0.98 x 0.67 |
| Weight, kg/lbs | 43 gr/ 1.52 oz |
* More modes can be supported via external software
Specifications are subject to change without notice or obligation and specifications are only guaranteed within the amateur radio bands.
Recommended Accessories
- Remote control using Pileup RPI server
- SMA to BNC adapter
- SMA to UHF adapter
- CCW MW/HF active loop antenna
- 2m filtered preamp
- High Pass Filter 100 MHz
Read more about ColibriNANO here.
| Weight | 0.05 kg |
|---|---|
| Dimensions | 11 × 3.5 × 3 cm |
Based on 0 reviews
Be the first to review “ColibriNANO USB SDR Receiver 0.1 to 55 MHz”
Related products
-
HanRongDa, Receivers, Adventure Products
HRD 747 AM/FM/SSB MW-UHF Mini Receiver
HRD-747 is a multi-band multi-mode mini radio with coverage of FM, MW, SW, AIR, CB, VHF, UHF, UBD and WX bands. AM, FM and SSB modes are supported together with many features found in much more expensive devices.
SKU: HRD747 -
Remote Control
NEO WiFi Smart Plug 16A3
The NEO WiFi Smart Plug 16A is a small switch that plug into the wall socket and connects to your Wi-Fi network. It can switch 230 volt AC loads up to 16A and is compatible with the Tuya Smart Life app, IFTTT or can be controlled using Amazon Alexa or Google Home.
SKU: NEO-WR02WE
There are no reviews yet.