Shop
Showing 241–260 of 323 results
-
Chokes & Transformers, Low Band Systems, RFI Prevention, RX Antennas
Receive Common Mode Choke
Common Mode Chokes from Low Band Systems removes unwanted noise and signals from the feedline of your receive antenna. It is a āMust haveā to keep your radio’s noise floor low and quiet, especially on 160, 80 and 40 meter bands!
SKU: rx-common-mode-choke -
Meshtastic, RAK Wireless
WisBlock Starter Kit
The WisBlock Starter Kit is a bundle of WisBlock Base RAK19007 and Core RAK4631 from RAKWireless. By prioritising power efficiency and management, the it is the perfect choice for solar powered off grid Meshtastic nodes, routers and repeaters .
SKU: RAKWIS -
LoRa 868 MHz Antennas, Meshtastic, Paradar Antennas
Paradar 868 Mhz SAW Filter
The Paradar SAW filter is crucial for LoRa deployments in urban environments. Why? Because 4G cellular towers in Europe and the UK, operating on 4G Band 20, work on frequencies as high as 862MHz. A high-gain antenna in an urban environment is going to pick up a lot of this RF energy, which your 868MHz LoRa device will need to filter out.
SKU: SAW868 -
ModMic
ModMic to Icom Modular Adapter
Adapter to connect the ModMic boom microphone to Icom transceiversĀ with an eight pole modularĀ connector (RJ45) including IC703, IC706MK1,Ā IC706MK2,Ā IC706MK3,Ā IC2000,Ā IC2000H and IC-7100. This adapter contains a circuit to power the ModMic from the transceiver, it should not be used with dynamic microphones. It also features a RCA female jack for PTT or foot switch.
SKU: MMA-ICMOD -
ModMic
ModMic to Yaesu 8-pin Adapter
Adapter to connect the ModMic boom microphone to Yaesu transceivers with an eight pole microphone connector. This adapter contains a circuit to power the ModMic from the transceiver, it should not be used with dynamic microphones. It also features a RCA female jack for PTT or foot switch.
SKU: MMA-Y8P -
ModMic
ModMic to Icom 8-pin Adapter
Adapter to connect the ModMic boom microphone to Icom transceivers with an eight pole microphone connector. This adapter contains a circuit to power the ModMic from the transceiver, it should not be used with dynamic microphones. It also features a RCA female jack for PTT or foot switch.
Replaced byĀ ModMic Transceiver Adapter v2.0, choose Icom 8-pin version before adding to cart.
SKU: MMA-IC8P -
ModMic
ModMic to Kenwood TS-480 Adapter
Adapter to connect the ModMic boom microphone to the Kenwood TS-480 transceiver. This adapter contains a circuit to power the ModMic from the transceiver, it should not be used with dynamic microphones. It also features a RCA female jack for PTT or foot switch.
SKU: MMA-480 -
Meshtastic, zerofox3D
Bender Case for HeltecV3
Designed by zerofox3D, Bender is the wildly popular case for the Heltec V3 LoRA Meshtastic powered Radio node. It features a bay for an 18650 battery and support for a full size SMA connector so a variety of antenna’s can be used. Just add your own HeltecV3 and you have a Meshtastic node!
SKU: BEND -
-
-
RadioSport Headset Cables, RadioSport Radio Jumper
RadioSport 7-Pin DIN Adapter for Icom PTT
radiosport PTT adapter for Icom radios with a PTT interface on a rear panel. Fits popular Icom models like Icom IC-736/737/738, IC-746/756 (all), IC-7600/7700/7800, and IC-7610, also IC-7200 or IC-7300 with ICOM OPC-599 Cable Splitter.
SKU: RS-DIN7-RCA