-
Expert Electronics, SDR Transceivers, Transceivers
SunSDR2 PRO HF, 6m & 2m Transceiver
SunSDR2 PRO is a direct sampling SDR transceiver developed for serious DXing and contesting. It covers all HF bands plus 50 MHz and 144 MHz VHF bands with a general coverage receiver. It combines high performance in a small package and has a LAN interface for maximum flexibility. Remote control over DSL or mobile 3G and 4G connections provide a full SDR experience using the Expert Remote System.
SKU: SS2PRO
SunSDR2 PRO HF, 6m & 2m Transceiver
In stock (can be backordered)
SunSDR2 PRO is a direct sampling SDR transceiver developed for serious DXing and contesting. It covers all HF bands plus 50 MHz and 144 MHz VHF bands with a general coverage receiver. It combines high performance in a small package and has a LAN interface for maximum flexibility. Remote control over DSL or mobile 3G and 4G connections provide a full SDR experience using the Expert Remote System.
2,132.68 $
In stock (can be backordered)
The SunSDR2 PRO transceiver was designed for advanced operation on HF and VHF bands, even the most demanding operator will be surprised by its capabilities. Modern hardware along with the ExpertSDR software makes this high-performance SDR transceiver the perfect base station and at the same time perfectly suitable for field operations.
SunSDR2 PRO Main Capabilities
- Independent RX path based on DDC (Direct Down-Conversion) architecture
- Independent TX path based on DUC (Direct Up-Conversion) architecture
- 2 software RXs + SubRX for each of them (4 slices total) + independent wideband Bandscope up to 80 MHz
- A remote control operation, using it, you connect PTT and CW-key to the E-Coder panel. Microphone and E-Coder are connected to the remotely set up PC
- TCI interface for seamless connection with third-party software, the list of software with TCI support
- Professional TX processing module provides the most advanced tuning capability for voice operation
- ExtCTRLÂ connector to control external devices with 8 powerful keys with open collector
- ALCÂ connector for external power amplifiers*
- Supports use of VHFÂ transverters**
- An opportunity to use the transceiver as a signal generator via DAC OUT connector (SMA connector)
- An opportunity to use external filters in the middle of the RF path, using ADC IN and RX OUT (SMA connector)
- Monitoring delay in CW mode is about 5-6 ms
- Input for external 10 MHz reference oscillator
- An opportunity to use the transceiver in SO2V mode
- Full duplex or half-duplex modes***
- Antenna switch with 2 HF antenna connectors and separate VHF antenna connector (Mini UHF connectors)
- Internal power-meter for HF and VHF bands and SWR-meter for HF band
- Ethernet LAN interface provides a fast and reliable connection to PC
* ** *** These functions are supported by the transceiver’s hardware, but are not implemented in the ExpertSDR2 software. They will be supported in the future ExpertSDR2 software releases.
SunSDR2 PRO Block Diagram
SunSDR2 PRO Specifications
RF ADC, bit @ MHz | 16 @ 160 |
ADC type | LTC2209 |
RX Frequency range | HF 0.1 to 65 MHz, VHF 95 to 155 MHz |
Independent software receivers | 2 + 2 SubRX |
Sample rate, kHz @ bit | 39; 78; 156; 312 @ 24 |
Bandscope, MHz | 80 |
RX HF filters, MHz | 65 MHz LPF or 9 x octave BPF |
RX VHF filters, MHz | WideRX: 95-155 or SAW filter for 2M: 144-148 |
BDR on HF, dB | 130 |
BDR on VHF, dB | 114 |
Sensitivity, uV | 0.2 |
DR IMD3, not less dB | 98 |
RMDR, dB | 110 |
ATT/Preamp, dB | -20; -10; 0; +10 |
VHF LNA, dB | +22 |
RF DAC, bit @ MHz | 14 @ 640 |
TX Frequency range, M | All amateur bands 160-6; 2 |
Output power on HF, W | 15 (up to 20) |
Output power on 6M, W | 15 |
Output power on VHF, W | 7 (up to 8) |
TX IMD3, dB | 25-30 on HF/VHF |
Local oscillator TCXO, MHz +/- ppm | 20 +/- 0.5 |
External 10 MHz oscillator input | + |
Built-in audio codec, bit | 24 |
RF input/output | 2HF, 1VHF (Mini_UHF) ADC IN, DAC OUT (SMA) |
PC interface | LAN 100 Mbit |
DC voltage range in RX/TX, V | 10…16/ 12…16 |
Recommended DC voltage, V | 15 |
Current consumption RX/TX, A | 1.25 / 5 |
Power consumption RX/TX, W | 19 / 75 |
Operating temperature, °C/°F | 0…+50/ +32…+122 |
Dimensions L x W x H, cm/inches | 19.0 x 17.0 x 5.0/ 7.48 x 6.69 x 1.97 |
Weight, kg/lbs | 1.5/ 3.31 |
Specifications are subject to change without notice or obligation and specifications are only guaranteed within the amateur radio bands.
SunSDR2 PRO – What’s in the Box
- SunSDR2 PRO Transceiver
- LAN-cable 1.8m for connecting to local network
- Power cable 2.0m for connecting to power supply
- Two 6.3mm phono male to 3.5mm phono female adapters to connect a headset to the radio
- Mini UHF (male) to SO239 (UHF/PL female) pigtail adapter with 30 cm  RG58 coax.
SunSDR2 PRO Recommended Accessories
- E-Coder control panel for ergonomic contest or DX operation
- E-Coder Plus control panel with higher resolution VFO encoder
- E-Coder 2Â control panel with sound card for local monitor of remote radio
- ModMic boom microphone
- UHF to Mini-UHF adapter
- UHF to Mini-UHF pigtail adapter
- UHF to BNC adapter
- PTT control cable for external power amplifier
- PTT Control cable with Fan control output
- PTT & Band Data cable for SPE Expert amplifiers
- PTT Control Cable for Xiegu XPA125 100W amplifier
Weight | 2.38 kg |
---|---|
Dimensions | 32 × 24 × 9 cm |
Marc (verified owner) –
Totally different level from traditional radio!
Tons of custom settings, super nice filters, waterfall, bandscope, t.eq, etc, etc
Superb Forum & Support!
Marc –
Tilman, SM0JZT –
20W may not sound like a big number, but ample of power for day to day traffic. If you need more output, just put a amplifier behind.
Nice to be able to run 2m with a useful spectrum view in the normally very uncrowded band.
Tilman, SM0JZT
Tilman, SM0JZT –