OM 2500A Remote Control
Available on backorder
Share this:
Remote Control expands possibilities of using OM 2501A up to 10 meters away from your operating position. When needed it is also possible to connect the Remote Control unit to a LAN network and control over the internet it using a special software.
Delivery time 2-3 weeks.
613.51 $
Available on backorder
General description of the OM2500A Remote control
Remote Control expands possibilities of using your OM2501A power amplifier up to 10 meters away from your operating position. When needed it is also possible to connect Remote Control unit to LAN network and control it using special software (not part of this package) to unlimited distance.
Package includes:
- Remote control for OM2501A
- Power supply 230V / 12V, 600mA
- 10m patch lead to link Remote control with OM2501A PA
| Label | Description |
| ON / OFF | – Standard ON / OFF switch. On state is indicated by green LED on the switch |
| OPERATE | – button controls the operating state of the PA. When i noperating mode green LED is lid |
| POWER | – Power LED indicates connection of power supply. 12V / 500 mA |
| FAULT | – Red Fault LED indicates fault on PA. It shall be lid on any fault condition! |
| STBY | – yellow LED indicates Stadby state of the PA |
| TUNE | – yellow LED will be lid if PI tuning circuit indicates that additional tuning is necessary |
| GRID | – indicates 2nd grid protection. Trigered if safe screen current has been reached ) |
| SWR | – Yellow LED will indicate excessive reflected power on PA’s antenna socket |
| DRIVE | – will be lid if maximum drive power has been exceeded |
| OUTPUT POWER | – 30 segments bar graph will indicate peak output power |
| LAN | – Standard RJ45 connector – LAN Interface for remote access |
| ON | – Main ON / OFF switch. (Cut’s off 12V supply to unit) |
| DC 12V | – power jack (5,5 / 2,1) for supply of 12V / 600mA |
| CAL | – calibration potentiometer ( if necessary to synchronize the power bar graph with bar graph on OM2501A ) |
| PA | – socket for direct connection to OM2501A PA |
Warning:Â Please pay extra attention not to use PA socket as LAN socket as harmful voltages could damage your Ethernet devices such as switches, PCs etc. Use only supplied 10m cable to connect your PA with Remote Control unit.
Grounding
The Remote control box has to be grounded properly! Connect the screw on the rear panel of the box to your local grounding system with a copper-cable; use a cross-section of 4 mm2 at least. Connect your transceiver and amplifier to the same grounding system of your shack carefully! If you use a power amplifier with higher output you have to be aware that your grounding system works properly. All parts have to be grounded to the same system. Use short cables and make sure that there are good contacts! Otherwise you run the risk of damaging your equipment, having problems with TVI/BCI or your signal may be distorted.
Deployment instructions:
- Connect unit with the OM2501A power amplifier using the supplied cable
- Supply 12V DC voltage to power socket using supplied PSU
- Check that green POWER LED and yellow STBY LED are both lid. Shall any connection fault occur it will be indicated by sequenced POWER and STBY flashing and FAULT led will be lid constantly.
- Turn the PA on using the ON button. Tube heating process will begin. This will be indicated by green LED on the ON button and by flashing of four LEDs (TUNE,GRID,SWR,DRIVE) (WAIT led will be also lid on the PA’s front panel)
- After heating process PA is now ready to be turned into operating mode using OPERATE button. Use same switch to enter STBY / OPERATE (works as reset shall fault state occur)
Warning:Â It is absolutely a must to observe and follow all best practices and safety precautions as well as your local health and safety law and fire / electricity regulations. We do recommend using visual remote control like Web Camera etc.
LAN Connection
Remote unit is interfaced to LAN via XPORT made by Lantronix (type XP1001000-05R). More info can be found at www.lantronix.com .
Default factory settings of XPORT are:
IP address:Â 192.168.1.222 (first series can be: 192.168.1.101)
Mask:Â 255.255.255.0
Gateway:Â 192.168.1.1
These are strictly default settings. You can modify any of these by going to XPORT web GUI via your web browser. We do not recommend changing any other parameters of the XPORT interface as loss of communication can be caused by doing so. There is no default user name or password. It is highly recommended to secure web interface with username and password.
For remote control and monitoring over LAN special software is needed. It is available free of charge; it can be downloaded from the following address:
https://www.om-power.com/download/HF_PA_Manager_v1.51-setup.exe.
Related products
-
SDR Transceivers, Expert Electronics, Transceivers
MB1 PRIME High End DUC/DDC Transceiver
The MB1 transceiver is a game changer, it’s a transceiver and a PC in a single package. It has a classic design, developed over several decades, with the most advanced DUC/DDC SDR technologies – Direct Down Conversion (DDC) and Direct Up Conversion (DUC) and a fully featured high-end personal computer with an Intel Core i7 processor on board.
Latest production run includes an updated mother board,  I7-9700 CPU, 16GB DDR4 RAM, 500 GB SSD. TX IMD3 has been improved with up to 7 dB! (See updates below colorised in red).
Scroll down to see the video presentation, specifications and to download a brochure.
Read our blog series about the MB1 here.
SKU: MB1P -
OM Power, Power Amplifiers
OM2000+ HF & 6m 2kW Power Amplifier
The OM2000+ linear amplifier is designed for all shortwave amateur bands from 1.8 to 29 MHz (including WARC – bands) plus 50 MHz and all modes. It is equipped with a ceramic tetrode FU-728F and delivers 2000 watt on HF and 1500 watt on 6 meter.
Reviews
WU2M – “This amp is a powerhouse!”
F8DQL – “It’s impressive!”Built on order, delivery time 2-3 weeks.
SKU: OM2000+ -
ModMic, Audio & Sound, Transceiver Accessories
ModMic USB Attachable Boom Microphone
The New ModMic USB Attachable Boom Microphone is great for SDR Transceivers where the mic connects to the PC. The ModMic Uni is a high quality uni-directional electret microphone on a boom that attaches to any headphones to create your perfect headset.
SKU: MODMIC-USB
